What is Hydraulic brake booster?
A hydraulic brake booster (also called a Hydroboost) is a braking system that replaces your vacuum booster. It gives approximately 2-3x the braking pressure for the same amount of pedal pressure as vacuum operated brakes. It runs off of your power steering pump.
If it runs off my power steering pump and my pump dies, the powers steering belt brakes, or the engine quits how do I stop?
On a vacuum based system, if your engine quits or the booster goes bad, the system reverts to manual brakes. On a hydroboost system, there is a nitrogen-charged canister that is an accumulator for residual pressure in the event of losing the pump. The accumulator is the gold cylinder usually seen on the right side of the unit, and it's filled with 1,500 psi of nitrogen and when your pump is running it fills the chamber with power steering fluid and compresses a piston. Provided you have a full charge of nitrogen in your accumulator (yes they can go bad) you will have 2-3 full power brake applications in the event you lose the pump. After that, the system reverts to manual brakes.
Can I use my existing master cylinder or do I need to buy one with the Hydraulic brake booster?
For Jeeps prior to 1974 we recommend replacing your OEM master cylinder (most cases will require it). If you change your Master Cylinder to the one we provide, you must convert to front disc brakes and either run adapters for your current brake lines or redo all of your brake lines. You may also want to add a proportioning valve to balance the system.
Does it matter how I hook up the T-fitting for the return line?
It is critical that the T-fitting is installed in only one way or you will have trouble with your system. This is the correct way:
Can I fit a flared hose fitting to metric o-ring ports?
Yes, Hydratech Braking sells flare adapters that fit in the metric ports. Also, check out their low profile banjo fittings for increased clearance if required.
What if my truck has drum brakes all the way around, will this still work?
Possibly, but the set up is more involved. You will need to source a few more parts and drill two additional 3/8" holes in your firewall.
Will I need to add a residual pressure valve to my brake system to use this with all discs or all drums, and which one would I use?
Yes, if you have all drum brakes you may wish to add a 10lb residual pressure valve to the line that serves your front brakes although some who've done this will tell you it's not necessary. If you plan to run all discs you are best off to add a 2lb residual pressure valve to the line that serves your rear brakes, but again some will tell you they felt it wasn't required.
The rest of my braking system is not in great condition. Will I still see improved braking?
It is imperative that you bring your system up to safe operating standards prior to considering installing a hydraulic brake booster system. The increased pressure that the system will see can cause a deteriorated or worn system to fail.
What do you recommend for power steering fluid?
We recommend GM Goodwrench part number: 89020661
A hydraulic brake booster (also called a Hydroboost) is a braking system that replaces your vacuum booster. It gives approximately 2-3x the braking pressure for the same amount of pedal pressure as vacuum operated brakes. It runs off of your power steering pump.
If it runs off my power steering pump and my pump dies, the powers steering belt brakes, or the engine quits how do I stop?
On a vacuum based system, if your engine quits or the booster goes bad, the system reverts to manual brakes. On a hydroboost system, there is a nitrogen-charged canister that is an accumulator for residual pressure in the event of losing the pump. The accumulator is the gold cylinder usually seen on the right side of the unit, and it's filled with 1,500 psi of nitrogen and when your pump is running it fills the chamber with power steering fluid and compresses a piston. Provided you have a full charge of nitrogen in your accumulator (yes they can go bad) you will have 2-3 full power brake applications in the event you lose the pump. After that, the system reverts to manual brakes.
Can I use my existing master cylinder or do I need to buy one with the Hydraulic brake booster?
For Jeeps prior to 1974 we recommend replacing your OEM master cylinder (most cases will require it). If you change your Master Cylinder to the one we provide, you must convert to front disc brakes and either run adapters for your current brake lines or redo all of your brake lines. You may also want to add a proportioning valve to balance the system.
Does it matter how I hook up the T-fitting for the return line?
It is critical that the T-fitting is installed in only one way or you will have trouble with your system. This is the correct way:
Can I fit a flared hose fitting to metric o-ring ports?
Yes, Hydratech Braking sells flare adapters that fit in the metric ports. Also, check out their low profile banjo fittings for increased clearance if required.
What if my truck has drum brakes all the way around, will this still work?
Possibly, but the set up is more involved. You will need to source a few more parts and drill two additional 3/8" holes in your firewall.
Will I need to add a residual pressure valve to my brake system to use this with all discs or all drums, and which one would I use?
Yes, if you have all drum brakes you may wish to add a 10lb residual pressure valve to the line that serves your front brakes although some who've done this will tell you it's not necessary. If you plan to run all discs you are best off to add a 2lb residual pressure valve to the line that serves your rear brakes, but again some will tell you they felt it wasn't required.
The rest of my braking system is not in great condition. Will I still see improved braking?
It is imperative that you bring your system up to safe operating standards prior to considering installing a hydraulic brake booster system. The increased pressure that the system will see can cause a deteriorated or worn system to fail.
What do you recommend for power steering fluid?
We recommend GM Goodwrench part number: 89020661
Comment